Results / Sign Up

2024 Elk River Smoke N Show

Sherburne County Fairgrounds West Hwy 10, Elk River, MN

Saturday June 8th Sled “Equalizer” Pull starts at 5:00 pm.

Weigh in starts at 4:00pm Registration closes at 6:00 pm

$25 advanced entry fee by June 1st,2024, or $30 day of pull (One free pit pass with driver)

Admission: $10.00 for 13 years & up, $5.00 for children ages 6-12

Pit Entrance requires a signed liability waiver. Outside alcohol is prohibited, NO coolers in grandstands.

GENERAL PULL RULES

  • A liability waiver MUST be signed by ALL
    PULLERS & PIT ENTERIES
  • Outside alcohol is prohibited, NO coolers in
    grandstands.
  • Conduct self with good sportsmanship
  • No riders
  • All judges’ decisions are final
  • Top 3 finishers may be requested to rescale
  • Hooks limited to one per vehicle
  • No first puller re-pull option. No restart after
    100ft
  • All VEHICLES one fuel ONLY.
  • No speed limit in any class
  • Hitch height not to exceed 20”
  • 3 1/2” hitch opening
  • Weight not to extend more than 24” from front
    of vehicle

TRACTOR

Farm Stock 5,000-7,000-9,000-12,000-18,500 (Payouts $200, $150, $100)

  • Factory stock motor, carburetor and drive train for that make & model
  • Stock or factory replacement turbo allowed on 12,000 and over.
  • 9,000 & below NO turbo allowed
  • No cut tires. (18,500 duals allowed)
  • Stock injection pump for make & model of tractor
  • Governors required
  • Safety equipment strongly encouraged

Hot Farm 12,000 (Payout $200, $150, $100)

  • Factory stock motor, drive train for make & model, OEM inj. pumps, water injection
  • 3X3 turbo
  • No cut tires
  • Cross bolted exhaust
  • Air shut-off
  • Scatter blankets or ¼” plate is preferred
  • ROPS
  • Wheelie bars

Hobby Stock 10,000 (Payouts $250, $175, $125)

  • 3×3 turbo
  • One fuel, no nitrous or oxidizer
  • Cross bolted exhaust
  • Scatter blanket or ¼ plate
  • Breakaway
  • Dead man throttle
  • Roll cage
  • Wheelie bars
  • Fire extinguisher

Open Classes 7,000- 10,000 (Payout $275, $175, $125)

  • Cross bolted exhaust
  • Scatter blanket or ¼ plates
  • Breakaway
  • Dead man throttle
  • Roll cage
  • Wheelie bars
  • Fire extinguisher
  • Helmet & fire suit

SEMI TRUCKS

20” hitch height for ALL semi truck classes. (Hitches provided)

Semi Trucks Road – 1 Weight Class

(Payout $350, $250, $150)

  • Fifth wheel plate
  • No chain up of axle
  • Proof of insurance
  • Current DOT with long form
  • Current cab card, license plate, & registration

Modified Semi Trucks

(Payout $400, $300, $200)

  • Safety equipment required

PICK-UPS TRUCKS

Stock Diesel Trucks 9,000 (Payout $200, $150, $100)

King of Street 8,500 (Payout $250, $175, $125)

Open Trucks 8,000 (Payout $275, $175, $125)

Stock Diesel 9000#

MUST HAVE HITCH WHEN YOU CROSS THE SCALE OR YOU WILL NOT PULL NO REFUNDS

All General Truck and Tractor Pulling Rules Apply.

  • STREET DIESEL: 9000 LBS max weight
  • ENGINE: Limited to light duty diesel engines factory installed in one ton or smaller trucks only. Engine must match the make of the truck.
  • DRIVETRAIN: Transmission, transfer case and axles must have been commercially available in a one ton or smaller truck.
  • BODY: Complete OEM floorboard and bed floor mandatory. The body must be an OEM truck body, including the full bed floor. The body must retain full sheet metal. Aftermarket hoods are permitted. The hood must be closed and securely latched while the vehicle is hooked to the sled. The complete OEM firewall and complete OEM floor pan are mandatory. Dually vehicles must have a dually bed! No bolt on duals.
  • INTERIOR: A complete interior including dashboard, door panels, etc. is mandatory. All factory controls (lights, signals, windows, wiper, etc.) must be retained and be operative as per tech officials. Must have two matching and fully upholstered front seats. The use of hand-throttle controls is prohibited. If the vehicle is equipped with heavily tinted drivers side windows the window must be rolled down during the hook.
  • DRIVERS RESTRAINT SYSTEM: The OEM restraint system is mandatory and must be worn.
  • STREET EQUIPMENT: Complete headlight and taillight assemblies are mandatory and must be operative. Complete OEM windshield and windows are mandatory. Windows must be operative per factory specifications; that is, they must open and close via OEM electrical or mechanical means.
  • BATTERIES: The batteries must be securely mounted. Must be in stock location.
  • TURBOS: Limited to one stock or stock appearance turbo – (6.4 Power stroke may run factory compounds with factory inducer size) all trucks must run an air filter. Air to air intercoolers only. 6.7 Powerstroke can run stock intercooler. The Tech Inspector has final discretion on turbo ruling. No swapping manifolds ex (2nd gen swaps). The cylinder head must remain factory width and length. The turbo on the top three winning trucks may be subject to being checked . It is the pullers responsibility to gain access to turbo for tech inspector. If turbo is found to be out of spec that truck will be disqualified.
  • EXHAUST: No hood stacks allowed. Exhaust must exit past the drivers compartment.
  • FUEL: #2 DIESEL FUEL ONLY. No propane or nitrous oxide allowed. Must have a factory fuel tank.
  • Fuel Injection Pump: Aftermarket electric lift pumps allowed (FASS, AIR DOG, etc.)
  • COOLING SYSTEM: Radiators must be in the stock location and be of at least stock size. Block must circulate coolant freely – no hard-blocks allowed. Electric fans not permitted, no electric water pumps. Heads must flow water freely. No ice box allowed.
  • HITCH: 26” max hitch height. Receiver (Reese) style hitch only – no draw bar hitches allowed. Hitch may be bolted or welded to the frame for mounting and must be stationary in all directions. No extension or any part of the hitch may extend beyond the centerline of rear axle housing. A hitch may be mounted below or between frame rails. No bracing to the axle allowed. The hook point must be no closer than 44” of the centerline of the rear axle. Hook point must be located rearward of tailgate location. No trick hitches. Tech officials have final ruling on hitch. Must have a 3” wide by 3 3⁄4” deep opening. Secured with a minimum 5⁄8” grade 8 bolt or pin. Hook point must be rigid, cannot swivel. MUST HAVE HITCH WHEN SCALED IN OR YOU WILL NOT PULL!!!!!!!!!!!!!!!!
  • SUSPENSION FRONT: OEM suspension only. Steering must be OEM belt driven. The upper mounting point for strut assemblies must be in a factory location. Strut tower braces, lower tie-bars, sway bars and limit straps are permitted.
  • SUSPENSION REAR: An OEM-style suspension is mandatory. Lowering or raising the vehicle’s height with suspension modifications is permitted. Traction bars are permitted; they must be bolted on only. Lift kits are allowed. No welding or use of clamps is allowed on leaf springs. No blocked suspension allowed.
  • BRAKES: Four-wheel hydraulic brakes are mandatory.
  • CHASSIS: The OEM chassis is mandatory. The engine must be in the OEM location for the body used. The vehicle must retain the full OEM chassis.
  • TIRES: DOT tires only. Factory equipped dually is permitted Must run dually wheels on front axle. All six tires must be same size
  • Weight: 9000 lbs max weight. Ballast can be added to the truck but must be secured. No weights allowed in the front floorboard area. No hanging weights forward of the front bumper. Front bumper must be in the stock location. No loaded front bumpers. After market and homemade bumpers will be allowed at techs discretion.

King of the Street 8500#

MUST HAVE HITCH WHEN YOU CROSS THE SCALE OR YOU WILL NOT PULL NO REFUNDS

All General Truck and Tractor Pulling Rules Apply.

This class is designed for Street Modified Pickups

  • Trucks must pull at weight of 8500 pounds or less.
  • Front hanging weight or weight boxes allowed. Aftermarket front bumpers are allowed. Homemade bumpers will be at the discretion of the tech officials. Any additional weight must be secured in the truck box. No weights allowed in cab.
  • Must have a factory OEM truck body including pickup box with full bed floor. Must have complete interior minus the back seat with all working components. Fiberglass hoods, scoops, and roll pans are allowed. Must have an OEM chassis and four wheel working brakes and OEM suspension. Air bags or solid removable blocking is permitted Can only be bolted on one side. Lift kits are allowed.
  • Batteries must be in the stock location. Radiators must be in the stock location and be of at least stock size. Electric cooling fans are permitted.
  • An OEM transmission, transfer case, and drive axles must be used. Traction bars on rear are allowed but must have a safety loop within one foot of the front mount of the bars. No pro fab transmissions.
  • Must use OEM engine blocks that circulate coolant freely. Must have all factory driven accessories. Accessories must be powered by a crankshaft driven serpentine or V belt.
  • No electric water pumps
  • No hood stacks allowed.
  • Multiple high pressure fuel pumps are allowed. Fuel must be #1, #2, or Soy/Bio diesel and commercially available. OEM fuel tank must be used. No propane, NOS, or water injection allowed. Air to air intercoolers only are allowed. No fuel cells.
  • Hitch must be a Reese style receiver hitch with a 3.5 inch hole exposed at the rear of the vehicle. Additional hitch bracing is allowed.
  • Maximum hitch height is 26 inches. Final decision on the legality of any hitch is up to the tech officials and board members.
  • Tires must be DOT street tires inch. Siping tires is allowed. Factory duals are allowed.No bolt on duals allowed. Must have factory dual box. Vehicles must retain factory wheelbase and track width.
  • Any box turbocharger configurations are allowed. Chargers must retain all piping. No open chargers allowed. Truck must be able to be street driven.

Open Diesel Trucks 8000#

  • All General Truck and Tractor Pulling Rules Apply.
  • A weight of 8000lbs or less.
  • Maximum of 3 turbochargers of any size in a 2 stage configuration.
  • Must have all safety equipment.
  • Must have kill switch electric or air.
  • Must have all u joints shielded. Total of 5 loops per shaft.
  • Fire Jacket and pants if the cab has been cut out in any way. Jeans required if no cab
  • modifications.
  • Leather boots or SFI shoes.
  • Helmet must be worn.
  • Fire extinguisher within reach of the driver.
  • Exhaust must point up.
  • Water injection allowed.
  • Two 3/8″ bolts in a cross pattern as close to the turbo as possible.
  • Maximum of 35″ tire.
  • An engine from one ton or less truck.
  • 26″ Hitch Height.

Get in Touch with Us

4 + 7 =